Cat flaps let your cat go inside and out as they please without you needing to let them in or out. They can also help prevent your cat from toileting in the house.

It is much easier to put the cat flap on a Upvc panel than on a glass one, but you will require some expertise and right tools.

Take a measurement of the door

The installation of a cat flap in a front door could be difficult, but provided that the Cat Flap in upvc Door Panel flap is of the correct one and you follow the directions it shouldn't be too difficult. We will show how to trace the shape, use a jigsaw to cut out the door's opening and then finish the job by attaching the cat flap to the door. This will ensure that the flap stays in place and shields the door from rain and wind causing damage.

To determine the size of the cat flap that you require, measure your pet's width. This will let you select a cat flap that is big enough for cat flap in Upvc door panel your pet to go into the house and exit without having to open the door every time.

Once you have the measurements, you can determine the location on the door where the template should be placed, typically this is done using an X, but some kits come with an illustration that outlines where to drill. If yours does then stick it to the door and draw a line around the door. If your door has a sill or moulding along the bottom edge of it then make sure you have clearance from these because this will ensure your cat's safety and prevent them gaining access to your home.

Next put on your eye protection as well as a dust mask and using a jigsaw start cutting along the line you have pencilled in, don't try to push the blade too hard because this could cause it to cut more quickly than you want it to. If you own a square that you have cut, use it to ensure that you're cutting properly and also to ensure that the hole is in a rectangle. Once you are satisfied with this you can begin to take off the remaining door material.

Draw a Line

The cat flap lets you to let your pet inside and outside without worrying about unwanted visitors or unwelcome gifts. It also prevents draughts, and helps to keep your home's temperature in check. However, putting a cat flap in your door might seem like an overwhelming task for those who have never done it before. This can lead many to hire a professional carpenter or joiner to do the job instead. While this is definitely an option, it's possible to complete the task yourself if you own the right tools and follow the instructions with care.

While this is far easier to do when using a timber door it is still possible to do this in uPVC doors - although you must be careful not to scratch the doors, as this can invalidate your warranty. The first step is to take measurements of the door to ensure that it can accommodate the new cat-flap. This should be simple enough if you are using a standard uPVC door, however you might need to take more care if you have an insulated or composite kind of door, as they ensure that it is properly positioned and that it runs flush with all the other components of the door. You should make sure you have an sandpaper piece on the ready to smooth out any rough edges.

Wear any safety equipment you need to work with the power tool. If you're concerned about the noise, you can get a cordless jigsaw which is more quiet and easy to use.

You should only remove the material required to make the flap. It is essential to leave a little extra material to cover the wall of the cat flap. However cutting away too much could cause problems or even damage the frame of the door.

A door made of upvc could have a metal frame or a panel inside that could interfere with the microchip cat flap and if this is the case, you'll need to cut an over-sized hole to ensure that the metal doesn't touch the wall of the cat flap, if this is the case, it is important to fill in the gap and cat flap in upvc door panel seal it with water.

If you're installing a cat flap into the frame of a double glazed window with a frame made of metal, you'll need to talk to a professional who will supply you with a new pane of glass with the hole for the cat flap already drilled inside. It is much less expensive to do this than to attempt to fix the cat flap onto an existing pane of glass that hasn't been designed specifically for the purpose.

Install the Flap

Cat flaps let your pet move around whenever they want, allowing them the ability to unwind inside the house whenever they're feeling like it. If you have an uPVC front door, it might be hard to install the cat flap. This is particularly true if you do not own glass panels that is cut. Luckily, if you're happy to buy and install a new half-glazed uPVC panel, it's possible to add the cat flap double glazing flap to the doors. It's not as easy as making a hole in the door though and there are some things you'll need first to make sure it's secure.

A composite door panel typically comprises an flimsy plastic outer layer joined to a soft polystyrene insulating core. It is important to be cautious when cutting the material. This type of door typically includes a template that you can use as a reference for cutting the hole in the door.

After you've marked the position of the hole in your door, now it's time to put in the cat flap itself. You can purchase and install many different models including basic push-button operated models to ones that are activated by microchips that allow access only to your pet. However, no matter what type of cat flap you pick, it's important to make sure that your cat can use the flap without getting trapped outside in bad weather.

A circular fitting is superior than a square, because circles can be cut more securely into glass. This is because square holes leave the glass vulnerable to cracking if drilling is applied to it. This is also a safer option because you won't need to drill into the toughened glass that could break and hurt your pet or family. This is particularly important if you have young or elderly person at home who could be injured by shards glass.