How to Do a Door Lock Change

Door lock change is a simple and affordable way to improve your home security. The process is not for all. It requires a certain amount of skill and perseverance.

You need to replace the cylinder, which is located within the knob's body. The cylinder is responsible for recognizing the key as it is inserted into the lock.

Removing the old lock

First, you must remove the lock you have been using for a while. This is a relatively simple procedure, but there are a few points to be aware of. Make sure that the new lock fits your door. This will ensure that it fits securely, and doesn't leave a gap at the deadbolt or latch.

After you have removed the latch plate, you'll have to look for two bolts or screws in the casing's interior that are holding the casing to the lock halves. Take these screws off using a screwdriver before removing the lock off the door. If you have a mortise locking, there may be a set screw located at the base of the handle that binds it to the spindle. Make use of a screwdriver for removing this screw, then pull out the doorknobs.

You must also remove the latch and deadbolt plug from the hole in the door jamb. Install the new lock. If you are replacing a mortise you should measure the distance between the lock case and the door edge to ensure that your new lock fits.

You might want to change your lock for a variety of reasons, for instance, if you suspect that someone else has the key or you have a new roommate. In any event, you could save money by taking the lock off yourself, rather than hiring a professional to do it. It's easier than many people imagine, and it can be done in a few minutes.

Remove the handle and trim of your door. Then, you can pry the trim loose using a screwdriver that is flat. You will be able to pull off most of it, and in some instances the handles may fall off entirely. Next, look for a pinhole on the inside of the handle and then insert a straightened clip into it. This will activate the release mechanism, allowing you to remove the handle. Then, look on the interior side of the lock for another small tab, and then press it with a flat screwdriver. Once the spindle is removed, you are able to remove the housing and the cylinder.

Selecting a new locking system

You have many options when it comes to selecting a new lock. Look at different kinds of repair window locks, and find one that matches your door's style. Take into consideration the backset (the distance between the edge of the door and the center of the hole in the lock) and the cross bore (small hole in the frame of the door frame). Select a lock that is suitable for the door's thickness and swing.

Most door window locks repair are evaluated by BHMA and the American National Standards Institute to provide you with an idea of how they are able to withstand the rigors of use and how difficult to pick or disable. A lock grade 3 might be the ideal choice for a tranquil apartment complex in the country, while locks that are grade 1 might be more appropriate for an was used to lock your old lock with the new one by sliding it into the case, and then tightening the set screws. The process of reinstalling the component that connects the cylinder to a lock indicator stem is also important. It is done by pulling three small tabs on the back of the cylindrical using needle-nosed pliers. Attach the smaller bracket to the back of the cylinder. You must then install the latch plate and strike plate, as well as the retaining rings that are fixed to the top of the lock the cylinder.

Installing a new lock

Begin by measuring the width of your door if you are replacing a lock that is already in use. The majority of residential locksets come with a thickness of 3/8 to 1 3/4 inches. If your door is more thick it will require a thick window door lock repair kit that includes longer screws, longer tail pieces (for door knobs) or spindle extensions (for deadbolts).

The majority of locks come with a comprehensive instruction booklet that will help you install the new hardware. Before you begin, read the instructions to ensure you've followed all the steps. The manual will give you an idea of the level of skill that is required to complete the task. If you're changing locks for the first time, you might want to ask an experienced friend for assistance.

Before installing the new window lock repair, it's recommended to cover the openings with tape the old hardware. This will keep the screws from falling out of the holes and protect any tile you might have installed in the area. This will also protect your tiles from any damage caused by dirt, rust and grime. SECURAM Touch includes an ad-hoc strip of masking tape or gaffer tape. However, you can use any tape you have.

After taking off the screws that connect the lock's interior to the exterior, remove the lock immediately. It's important to do this as quickly as possible so that the lock doesn't end up accidentally closing on itself and damage the mechanism.

Install the new latch bolt in the upper cross bore of your new lock, if it has one. Make sure that you place it in the correct position, which will be marked by an arrow. Then, screw the latch plate onto the bolt.

Attach the deadbolt to the door jamb. Check the deadbolt several times by throwing it to make sure it extends into the strike plate. Follow the steps included with your electronic smart lock to program it. This requires downloading an app and registering your email address, confirming your identity, then accessing the wireless network to add your device.