boarding up and burglary repairs Up Windows and Doors Before a Storm Hits

Before a storm hits, boarding up your windows and doors can protect your home from damage. To do this, you should have a few items on your desk.

Measure the width and height of the window including the frame (not the trim or masonry surrounding the window). Take note of these measurements so that you won't forget.

Preparation

It is always recommended to board up doors and windows before an event like a storm or natural disaster strikes. This will help prevent damage to property and minimize loss of life. boarding up windows - https://fatahal.com - requires an extensive amount of preparation, like purchasing and measuring plywood boards as well as determining the exact dimensions of each window to be covered. Moreover, it takes time to cut the boards and install them correctly. The process can be simplified by preparing the boards when you learn of a storm approaching your area. By doing so, you can avoid a stressful last minute rush and make the process simpler for you and your staff.

Begin by listening to forecasters for weather and follow the guidelines provided by your local government. If you start earlier in the process, you will have more time to collect the materials and keep them in storage without being overwhelmed by a storm that is about to hit. It is possible that you will require a large amount of plywood to cover your windows, according to the severity and intensity of the storm. To ensure you get the right size, make use of a tape measure determine the height and width of each window opening. Be sure to consider the trim or framing surrounding each window, as and any sills with extended extensions when applicable.

Next, calculate the size of the plywood sheets you need by dividing your window's total width and height by 2. For instance, boarding up windows if the width of your window is 16 inches the thickness of each sheet should be 8 inches. If your exterior is made of wood make pilot holes in the plywood sheet to ensure it is aligned with the window frame below. This will help reduce splitting when you screw in the screws.

To make sure that the window's opening is larger than what one sheet of plywood can handle cut two sheets that are each half the size of the intended window and set them side-byside on the wall. Then cut a piece 2 by 4 inches (5.1 by 10.2 cm) lumber to the length of the connecting edges of the plywood sheets and then place it over the seam. Then screw 2.25 in (5.7cm) screws into the plywood sheet, and then through the bracing to join the two together.

Materials

To ensure security and safety for security and safety, boarding up windows and doors should be done using only solid materials that will not break under pressure or splinter in high winds. Plywood is the most common material for 24 hour boarding up service is strong enough to withstand high winds.

If you're building using concrete blocks, you can join the plywood using pan head screws galvanized and that are driven into the overlapping edges of the panels to the masonry or cinder block. You'll also have to drill pilot holes into the masonry and then screw corrosion-resistant screws through the holes. The project could take about three hours per window. It is essential to begin the project as soon when an alert for hurricanes has been issued. This will allow you plenty of time to finish the project before the storm arrives.

Maintenance

You should be prepared to board up your windows and doors before a severe storm. This will save you money on repairs and shield your home from further damage resulting from wind, rain debris, flying debris and other elements that can impact the windows.

The proper materials can make 24 hour boarding up service up more efficient and speedier. The most important thing is to accurately determine the dimensions of the windows you need to cover. This will ensure that the plywood or OSB will fit snugly and won't fall off easily. If you're using plywood ensure that you are using exterior-grade sheets, and consider adding an extra layer of protection.

After you have the OSB or plywood taken measurements, mark the locations where screws will be inserted into the board. Then, use a drilling machine to pre-drill holes into the plywood at 12-inch intervals. This will allow you to securely fasten the boards with hanger bolts during an emergency or disaster. After the storm is over and the local authorities have given the all-clear, Boarding up windows take out the bolts but keep them in case of emergency boarding up near me.

The next step is to install the plywood panels on top of the windows. This is a two-person task So, be prepared prior to starting. If you're using plywood, sand the edges to make them smooth so that they don't scratch paint or damage trim. Then, you can attach the plywood to the frame using screws that are corrosion-resistant and fit into the pilot holes. If your home is covered with shingles made of vinyl it is recommended to nail the plywood to the shingles rather than the wood framing underneath.

A window that is boarded up can be used to discourage burglars. Burglars will target a building that has a broken window or one that is not locked. They're also more likely break into the store that has been boarded up than one that isn't. This is something that business owners in retail should consider very seriously.