How to Do a Door Lock Change

Change your door lock is an easy and inexpensive method to increase the security of your home. However, the procedure isn't for all. It requires some skill and perseverance.

The cylinder is contained within the knob body. The cylinder is what recognizes the key once it's put into the lock.

Take off the lock that was previously used.

First, you must remove the lock that was previously in place. It is a fairly simple process, but it is important to keep some things in your mind. Make sure the new lock fits the door. This will ensure that it fits snugly and doesn't create a gap around the deadbolt plug or latch.

After you have removed the latch plate, you'll be required to search for two bolts or screws on the inside of the casing that are holding the casing in place with the two halves of the lock. Remove them with a screwdriver and then remove the lock from the door. If you have a mortise locking mechanism there is a set screw that binds the handle to the spindle. Make use of a screwdriver for removing this screw, then pull out the doorknobs.

Remove the deadbolt and latch plug from the door jamb. Then, you can install your new lock. If you are replacing a mortise Upvc window lock repair Cost you must also measure the distance between the double glazing window lock repair case and the edge of your door to ensure that your new lock will be able to fit.

You may want to replace your lock for various reasons, including if you suspect that someone else holds the key, or if you've an incoming roommate. In any event, you could save money by removing the lock yourself rather than paying a professional to do it. It's easier than many people imagine and can be done in a few minutes.

Remove the trim and handle from your door. Then, you can pry the trim away using a screwdriver that is flat. You should be able to twist off the majority of it and in some cases the handles may fall off entirely. Next, examine the handle for a tiny hole on the interior side and insert a straightened clip into it. This will trigger the release mechanism and allow you to take the handle from the door. The next step is to look at the inside of the lock for a small tab and press it using a flat screwdriver. After the spindle is removed, you can then take off the cylinder and housing.

Making a choice for a new lock

There are a lot of options available when it comes to choosing the right lock. Take a look at the various types of locks and select one that is in keeping with the style of your door. Consider the backset (the distance between the door's edge and the center of the hole for the lock) and the cross bore (small hole along the edge of the door frame). Also, ensure that you select a lock that is able to be able to fit the door's thickness and swing.

The majority of door locks are evaluated by BHMA and the American National Standards Institute to give you an idea of h.

After removing the lock cylinder and replacing it with a new lock by sliding the new cylinder into the case and tightening the set screw. The process of reinstalling the component that connects the cylinder to an indicator stem for a lock is also important. You can do this by pulling three tabs at the back of the cylindrical with needle-nosed pliers. Attach the bracket that is smaller to the cylinder's back. You should then reinstall the latch plate and strike plate, along with the retaining rings that are fixed to the top of the lock the cylinder.

Installing the new lock

Start by measuring the width of your door if you are replacing a lock that is already in use. Most residential locksets have a thickness of 1 3/8 inch to 1 3/4 inches. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll require a thicker door kit. This will include longer screws as well as a longer spindle extension or the tail piece for door knobs.

Most locks come with a thorough installation guide to assist you. Read the instructions carefully prior to beginning the process to make sure that you've followed all the steps. The guide will also give you an idea of the degree of skill required to complete the task. It is possible to seek out a friend who has had experience in changing locks for assistance if are changing a lock the first time.

Before installing the new lock, it's an excellent idea to put cover the holes with tape the old hardware. This will keep the screws from slipping out of the holes, and will protect any tile you might have put in the area. It will also protect your tiles from any damage caused by dirt, rust and grime. SECURAM Touch comes with the masking strip or gaffer tape, but you can make use of any tape you have.

After you have removed the screws that connect the inside of the lock section to the outside side then pull it out straight away. It is important to do this quickly to avoid the lock from closing accidentally and damaging the mechanism.

If your new lock has a latch bolt, fit the new latch bolt into the upper cross bore. Be sure to put it in the correct place, which is usually indicated by an indication on the faceplate. Then, screw the latch plate onto the bolt.

Finally, screw in the deadbolt and strike plates to the door jamb. Test the deadbolt by throwing it few times to verify that it extends all way into the strike plate and is completely secured. Follow the directions included in your electronic smart lock to program it. This involves downloading an app and registering your e-mail address, confirming your identity and connecting to the wireless network to add your device.