How to Replace a UPVC Door Replacement Lock

If your door lock is becoming stuck or isn't working as it should, it's time to think about replacing upvc door lock and handle it. It may seem like a complicated process but it's actually simple and doesn't require an expert locksmith.

A few basic tools along with a bit of patience and a lot of care will be enough to get the job done. Here's how you do it:

Take a measurement of the door

If you're struggling to lock your uPVC door, or it won't close or lock properly, it may be the time to replace it. If you've just moved into a brand new home, a tenant left without returning keys, or your multipoint gearbox is showing signs of wear and tear, switching the lock barrel to an entirely new one will offer an additional layer of security.

You'll need to take some measurements prior to buying the new lock. This will ensure that the new cylinder will fit properly and not compromise the security of your home. The backset is the most critical. This is the distance between the centre of your keyhole bore hole to the edge of your door. It's usually 2 3/8 or 2 3/4 inches. You can measure the length using a measuring tape and note down the results.

You will also need to know what the thickness of the faceplate is. This is the amount of thickness the faceplate covers the mechanism of the lock. If you can, buy an alternate lock manufactured by the same manufacturer, as they'll be made in the same way. If you can't find the name of the manufacturer or mark, just determine the width of your existing cylinder. You can also check this by placing a pencil over the keyhole and measuring from the bottom of the lock to the centre of the pencil mark on both sides of the cylinder.

Once you have the dimensions then you can begin to remove the old cylinder. Begin by loosening the screw that holds the handle in place with a Phillips-head screwdriver, then loosen the screws that hold the interior and exterior handles together. After these screws have been removed, you are able to remove the barrel screw on the exterior handle and remove the cylinder.

If the cylinder has become stuck in the lock, try using some WD-40 or another lubricant to help you pull it out. It's important to not force it out - forcible turns could damage the internal gearbox and cause additional issues with the lock. Consider upgrading to a lock with anti-snap and anti-bump protection. This will make it more resistant to attacks by thieves.

Source the Lock

Whether you're replacing lock in upvc door upvc door locks (Click In this article) an old lock following a burglary or upgrading for greater security There are a few things to bear in mind when selecting a new door lock. To ensure quality and fit make sure you purchase the correct size cylinder and from an established manufacturer. You'll require a few basic tools for the job, replacing upvc door Locks to the centre of the cylinder or handle - and also the type of lock you choose to ensure that the lock fits properly without compromising security.

After you've done this, it's now time to install the new lock. You should ideally prop the door open or lock it so that it does not close during the installation process. First, loosen the screws that hold the handle in place by using a Phillips-head screwdriver. Once they're removed you should be able to slide the handle's outer and inner parts apart.

Now you can begin to take off the old cylinder, which you'll need to do by removing it from its barrel. After you've removed the cylinder then you'll be able to install your replacement lock, ensuring that you follow the instructions for your specific model. Once it's in place, you can test the new lock by opening and closing the door lock replacement from the inside and outside as well as locking and unlocking it from the inside, and then testing it again.

There are a few reasons why you might need to change the lock on your uPVC doors. It could be because you've recently moved in and don't have a key, or that the previous tenant did not return it or you may prefer a more secure lock. Whatever the reason changing the lock's cylinder is straightforward and should only take about five minutes.

Whether you have a multipoint lock, or a single-point lock, they both operate on the same basic mechanism. They may have issues like closing issues or a jam. These can be caused by wear and tear, weather conditions or simply due to daily use. The majority of these issues are easily solved with a bit of maintenance or by hiring a locksmith.