How to Replace a UPVC Door Replacement Lock

If your door lock is jamming or simply doesn't work as it should, it's time to consider replacing it. The process might seem complicated but it's actually quite simple and doesn't require a locksmith.

A few tools of the trade along with a bit of patience and a lot of care should suffice. Here's how you do it:

Measure the Door

It's possible to replace your uPVC doors if they are experiencing difficulty locking them or they won't shut. If you've recently moved into a new property, or a tenant has moved out without returning keys, or your multipoint gearbox is showing signs wear and tear, replacing the lock barrel to a new one will provide an additional layer of security.

It is necessary to take measurements before buying an entirely new lock. This will ensure that the new cylinder will fit properly and not compromise the security of your home. The backset is the most critical. This is the distance that runs from the center of the keyhole bore hole to the edge of the door. It's typically 2 3/8 or 2 3/4 inches. You can measure the length using a measuring tape and note down the results.

You will also need to know what the thickness of the faceplate is. This is the size of the piece that covers the mechanism of the lock. If possible, purchase a replacement lock made by the same manufacturer since they'll be manufactured according to the same dimensions. If you are unable to locate the name of the manufacturer or mark, just determine the width of the existing cylinder. You can also measure the width of the existing cylinder by placing a pencil over the keyhole.

Once you have the measurements then you can begin to remove the old cylinder. Start by loosening the screw holding the handle with the Phillips-head driver, and then loosen the screws that connect the handles' exterior and interior to one another. Once these screws are removed, you can remove the barrel screw located on the exterior handle and pull the cylinder out.

If the cylinder is stuck in the lock, you can try WD-40 or another oil or lubricant. It is essential not to try to force it out. The forceful turning of the cylinder can damage the lock's internal gearbox. Consider upgrading to a lock that comes with anti-snap, antibump and anti-snap security. This will help to make it more resistant to attacks from thieves.

Source the Lock

When you are looking to purchase the latest door lock, you must take into consideration a few things. To ensure the quality and fit, make sure you buy the right sized cylinder from a reputable manufacturer. You'll require a few basic tools for the job including a screwdriver and a mallet made of rubber.

There are a variety of indications that your upvc door lock is about to wear out and will require replacement. Typical problems include visible damage to the lock or a handle that's loose and not fitting correctly. If the lock starts jamming or isn't locking at all, it's time to consider the possibility of replacing it.

After you've chosen the best lock, it's impoable replacement door lock.

A damaged door lock could be a huge hassle and can create a serious security risk. Locks on uPVC door are prone to malfunction, which is why it is crucial to check them regularly. In fact, experts suggest that you change your lock every seven years. If your lock is badly damaged or you aren't satisfied with its performance, professional help could be worth a look.

For uPVC, a simple pin system known as a euro cylinder will be utilized in the majority of cases. These are convenient to use and are not likely to break down, but they can still be susceptible to attack. It's therefore worth replacing your lock with a modern model that has anti-snap, antibump and anti-snap protection to prevent burglary.

The first step to changing your uPVC locks is to take off the handle. This will expose the old cylinder. It's not easy since there are screws concealed beneath the handles. Make sure you have a screwdriver in your bag. Next, you'll want to experiment with gently wiggling and tugging the cylinder until it becomes loose. Once it does then, you can take it from its socket.

When you have found a replacement lock for upvc door that is suitable then simply screw it into place and reverse the removal process. Be cautious not to tighten too much because this could cause the cylinder to get stuck in the door and not work as it should. Test the uPVC replacement door locks lock by opening and closing it both from inside and outside. You should now be able to lock and unlock it using your key! If not, make sure that the screws are tightened, then try again.

Install the Lock

Do some research to make sure that the lock you select is right for your door. You'll have to know the backset and faceplate measurements - that's the distance from the edge of the door to the center of the cylinder or handle - as well as the type of lock you choose to ensure that the new lock fits properly without any compromise in security.

Once you've completed this, it's time to install the new lock. It is recommended to prop the door open or fix it in a way that it doesn't shut during the installation process. First, loosen the screws that hold the handle together using a Phillips-head screwdriver. Once the screws are removed and the handle is free of screws, you can slide the internal handle and the outer handle away.

The next step is to take off the old cylinder. This is something you'll want to do by unscrewing it from its barrel. Once you've removed your cylinder, you'll be able to install the new lock, making sure that you follow the instructions for the particular model you have. Once the lock is in place, you can test it by opening and shutting the door from both the inside and the outside, locking and unlocking it from the interior and testing it again.

There are many reasons you may need to change the lock on your uPVC doors. You might have just moved in, and not had a key. The previous tenant may not have returned it. You may also prefer to upgrade your lock to one that is more secure. It should take no more than five minutes to change the lock cylinder.

If you own a multipoint lock, or a single-point lock, they all work on the same basic mechanism. This means they can be prone to problems occasionally, such as failing to close or becoming stuck. These problems are caused by weather conditions or wear and tear or just everyday use. Luckily, most of these issues can be fixed by just a little maintenance or the assistance of locksmith.