Replacing uPVC Window Handles

It is simple to swap the handles on windows made of upvc. The important thing is to ensure that the new handle is a good fit for the spindle cut out in the window mechanism.

If you follow the steps below any cockspur handle can fit most windows. The step height of the handle is important.

What to Look For

Many of the windows in the UK come with uPVC handles Over time, they can begin to show signs of wear and tear. If this occurs, the handle could become shaky or difficult to operate, making it essential to replace it. This is a fairly simple task that can be completed by anyone who is comfortable with basic hand tools.

The first step is to make sure the handle is firmly connected to the window frame, and is in an open position. Next, locate the screws or pins that secure the handle. These are usually located on the inside of the handle. They can be removed with an screwdriver or pliers.

Once the handle is loose it can be taken from its hinges by gently pulling it off. Then, you'll need to locate a replacement handle of the same dimensions and style. This can be accomplished online or in the local DIY store and it should take about five minutes with the help of a screwdriver.

One important factor to consider when replacing the uPVC window handle is the step height. This is the distance between the handle's base and the place it is placed within the frame of the window. This is a common measurement, and you should verify the step height before ordering a replacement handle.

There are various sizes depending on the type of handle. Inline handles can be found for uPVC windows with lug centres of 31mm while cockspur handles have lug centres of 43mm. Tilt and turn handles are often found on windows made of upvc door handle repair and they have a special design that allows windows to be slid up for ventilation, and then rotated to open the window fully.

The most common breakage in uPVC handles is that they crack inside rather than breaking off from the base section. This can make it difficult to open. It is important to make sure that any replacement handle has the same spindle as your original one.

Remove the handle that was previously used

Incorrectly installed or damaged window handles may cause your double glazed windows to close or open improperly and could even cause them to become stuck. There are a myriad of reasons for this, such as general wear and tear or the corrosion of the handle made of metal. In these instances it is crucial to replace the window handle as quickly as you can in order to prevent further damage or loss of function.

When replacing the handles on windows made of upvc, you should remove the handles that were previously installed from the window. Start by removing the screw with the handle when it is in a closed position. After you have removed the screw, you can remove the handle. It is possible to make the task simpler by using an electric screwdrivst remove it from the window by turning it to an open position. You should then be able see the size of the screw or pin that secures it. Use a ruler or a tape measure to determine the length the spindle is. Once you have the length of your spindle, it is possible to purchase a replacement of the exact same length.

The step height of a upvc window handle is also important to take into consideration when you are buying replacements. The step height is measured from the base to the point where the handle sits on the frame. It is typically about 21mm or 9mm for aluminum and uPVC. Dropping objects into the gap will allow you to observe how far the handle extends before it comes into contact with an obstruction.

Cockspur handles typically have different backset heights depending on the type of window they are placed in. Inline espag handles have a standard height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets, based on the window they are located in. This is because they feature an extension spur that extends from the handle and then locks over a cockspur wedge striker plate.

Install the new handle

If you've decided to replace the handle, ensure that it is aligned with the screw holes in the door lock handle repair and fix it using the supplied screws. Install the latch lever in the same manner as the handle that you are replacing in the event that you are replacing the patio door handle repair near me handle. Then, you can attach the door handle repair plate trim to hide the mounting screws.

Tip: To remove a metal head from a wedge made of wood, place the handle on the floor so that its wide end is level with the ground. Then, you can use an hammer and tap the thin end. Be careful not to damage the handle or the spindle.