Reasons to Change Door Lock

There are many reasons to change the door lock, from improving your home's security to redecorating your entrance. You might also have to change locks if your key gets stuck inside or is difficult to turn.

Change your lock is an easy project that even novice DIY homeowners can complete. Find the necessary materials to begin.

Remove the old lock

Before installing a new lock, it is essential to remove the old lock from the door. This is essential when you suspect that someone else may have a key to the home. It's an excellent idea after you've moved into a brand new home, experienced a burglary or a roommate moved in. The process is much easier than you imagine and can be completed within just a few minutes.

Start by removing the screws that secure the deadbolt faceplate onto the frame of the door. To remove the faceplate, you will have to remove screws from both sides. This will let you discover what's behind it and will provide you with a better understanding of what to do in the next steps.

After removing the faceplate you will have to remove the bolt along with the strike plate and strike plate. Remove the bolt from the door hole by using a screwdriver. If the bolt is rusty you may need to use a chisel smash it out. When using a chisel remove the bolt, make sure to not damage the door frame.

Make sure your new doorknob, deadbolt and lock fit in the existing holes in the window door Repairs locks glass hinges before removing the old one. A lot of hardware stores and big box stores have a wide selection of locks, and can help you choose the right one. Get help if the lock you bought isn't the right one for your door.

Find small depressions or notches in the handle and around the trim as you remove the old lock. If you find them, slide a straightened safety pin or flat screwdriver into them to open the handle and expose the screws beneath.

After you have removed the screw from the handle, you can start removing the knob. To do this, locate the set screw located at the base of the knob, and loosen it. Then, remove the spindle.

Install the new lock

It's a great idea to change the locks on your doors periodically particularly if you've had a break-in. It is easy, cheap and efficient to change the lock on your door. The majority of people can do it yourself with a screwdriver and some basic directions. You might also want to know how to change the lock's key to ensure that only you hold the key.

You'll need to purchase an additional lock that has the same keyway as the existing lock. Many locksmiths will rekey your lock for you at an additional cost but you can save money by doing it yourself. You can purchase an entirely new lock from a hardware store or online. Standard deadbolts can be fitted to most doors. However, you'll have to measure your door to ensure that it will fit.

Most times your new lock will include the cardboard template that will show you how it will fit on the door. This template can be used to drill the hole. It's a lot easier than having to measure each time. If the templ switch wires. Use a test light or digital meter to determine if the door lock actuator receives power and ground when the switches are turned on. If you notice an electric voltage switch on each switch activation, that means the switches are working and it's most likely the actuator that needs to be replaced.

If the switch seems to work however the actuator does not move when you turn the knob, it could be a problem with the actuator itself. The actuator cylinder has spring-loaded pins that stop the cylinder from turning until a key is inserted and it pushes the pins up to accommodate the key's height at the point of entry. Then, the cylinder to spin and unlock the lock body and allow the handle to latch.

If your door lock actuator is still malfunctioning, you can take the switch and wires from the actuator using a small screwdriver to release the locking bolt and remove the plastic cover which holds the electrical connector. Then, disconnect the door actuator from the lock and let it fall. Then, you should be able locate and remove the two bolts that are which hold the actuator in position. Once the actuator is removed, you should be capable of disconnecting the black electrical connector and then pull it out along with the actuator and lock assembly.

Replace the key

If your deadbolt that is keyed or door knob isn't working, you will have to reset it or replace it. It's not too difficult and can save you money. However, before you do this it is recommended to get a locksmith to examine the locks and check for any problems. This will give you peace of mind that your home is safe and secure.

Take off the exterior faceplate of the doorknob/deadbolt. There may be screws that are holding it in place, then use a screwdriver loosen them and then pull the faceplate out. Then you can use a flat-head screwdriver to remove the interior faceplate. After removing the faceplate you can remove the screw and bolt from the lock cylinder.

A locksmith can tell you whether you need to replace or rekey your lock. They can also offer guidance on the most effective security measures for your home. They can also make the necessary adjustments to your door and frame to ensure a perfect fit. They also offer the guarantee for their work.

You will need to purchase a brand new double glazed window lock repairs key before you are able to rekey it. It is essential to select a key that fits well in the lock. Using an incorrect key could damage the mechanism's internal mechanisms and prevent it from working. Insert the key into the lock to check its size. If the key sits flush against the plug, then it's the right size. If the pins stick up from the top of the plug the plug, then they're too long.

There are many reasons you might want to change the lock on your door, including:

If you're moving into a former owner's home or if you lose your keys, rekeying the lock is an affordable alternative than replacing it. It's also less invasive than a complete replacement. However, there are certain circumstances where rekeying your existing lock isn't possible. For example, if the lock is damaged or repeatedly jammed, it's probably time to replace it.