Repairs to uPVC Windows

uPVC is a great option for modern homes. They are durable, long-lasting and easy to maintain. In contrast to aluminium and timber, they do not rust or rot.

It is important to clean and oil UPVC windows and doors regularly. This will prevent unnecessary repair a window costs and increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home, and could even be fatal. It is important to ensure that your windows are in good condition.

Single-pane windows are fairly simple to replace, and they will usually fit into the frames that were previously in use very easily. However If windows with double panes are anchored by internal beading, it'll be more difficult to take out the existing panes and install new ones. In this case it is essential to buy plastic spacers to make sure that the new pane fits into the window frame.

If you are going to try to remove the window panes yourself it is crucial to wear the appropriate safety equipment that includes gloves with a thick layer of material and protective eyewear. It is also recommended to lay down a drop cloth before you begin working on the glass so that any shards will fall on the fabric instead of onto the floor, where they could be trampled upon and cause further damage.

Once the glass has been removed, it's a good idea to seal the gap with clear packaging tape or duct tape to stop water and drafts from entering the property until a professional can come out and fix the window. This also serves as an obstruction to prevent intruders from getting into your home. If the distance between the window and the door repairing is significant, you may prefer an alarm system that includes windows. This will give you the best of both.

2. Sagging

uPVC is durable energy-efficient, cost-effective and economical alternative to timber sash windows. However, over time, they may be afflicted by a variety of issues like sliding. A sagging window in uPVC can cause issues with light, draughts and even security. It's crucial to act when you realize that your uPVC windows are sagging.

Repositioning the hinges could aid in fixing a window which is sagging. To do this, you'll need open the window so that you can get to the frame. You can then unscrew both the hinges on the top and bottom with a screwdriver and adjust the hinges clockwise or counter-clockwise. Close your window to check the fit after having repositioned your hinges. If you're happy with the fit, you can tighten the screws to ensure that they stay in the right place.

If you are unable to reposition the hinges you may need to replace the seal. Rubber seals can dry out and lose their elasticity over time, which causes them to loosen. It is essential to replace your seal as quickly as you can to keep your uPVC window waterproof and draughtproof.

uPVC handles can also loosen up. This is often cau frame. It is also possible to be fixed by a uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault when your uPVC window is difficult to open or it opens in a breeze. Any competent DIYer can replace the hinges in a matter of minutes.

Like any mechanical part, hinges can be damaged over time. It's easy to change a window hinge but it's much easier if someone helps hold the frame.

Verify that the uPVC hinges are open and closed in the proper direction. Look for the arrows that are on each hinge to determine the direction in which the window should be opened.

Window hinges that aren't working properly could be caused by improperly opening the window in a particular manner or because of inadequate installation at the factory. Sending us a photo via our website will often solve the issue. We are more than happy to provide suggestions.

It is also essential to lubricate the hinges on a regular basis. This can be accomplished by applying a light engineering oil to the hinges, we recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It can also reduce the risk of a window getting stuck and stop corrosion. Ideally, you should perform this every year. WD40 and other solvent-based lubricants should not be used as they can damage your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by different things. First, the hinges because of wear and tear, may become displaced, which causes a gap to form where the sash meets the frame. If they're beyond repair, it might be necessary to get them re-aligned. Second, the interlock can also become unbalanced. This is located on the hinge's side and might require to be cleaned. In some instances it might be necessary to replace the hinges.

These seals can wear down or be damaged over time, allowing air escape. Replacing these with high-quality weatherstripping is a good way to keep draughts at bay. Another option is to replace the upvc window with low-emissivity glass, this will help in regulating indoor temperatures and will reduce the possibility of draughts.

The final method to cut down on drafts effectively is to use a draught-excluder. These are usually made of fabric tubes filled with a filler which can be put on top of your window sill. These will help to keep cold air out and keep your home warm and cosy!

With a bit of regular maintenance and repairs your windows made of upvc will provide an excellent level of security and insulation for your home. However, it is important to recognise that all windows have a life span and they may reach the point when it's more efficient to replace them than fix them. If you are experiencing problems with your upvc windows, it is best to seek professional assistance as soon as possible.