How to Do a Door Lock Change

Change of the door lock is a quick and cheap method to boost your home's security. This isn't for everyone. It requires a certain amount patience and skill.

The cylinder is located within the knob's body. The cylinder is what identifies the key when it is put into the lock.

The old lock can be removed

The first step to replace upvc window lock the door lock is to take out the old lock. This is a relatively simple procedure, but there are a few points to remember. Make sure the new lock fits your door. This will ensure that it fits securely and does not leave a gap in the latch or deadbolt plug.

After you've removed the latch plate, look for two bolts or screws on the inside of the casing, which secure the casing and halves of the lock together. Remove these screws using the help of a screwdriver, and then remove the lock out of the door. If you have a mortise locking system, there is a set screw that holds the handle to the spindle. Take off the doorknobs by removing this screw using the help of a screwdriver.

You should also remove the latch and deadbolt plug from the hole in your door jamb. Install your new lock. If you're replacing a mortise, you must measure the distance between your lock's case and the door edge to ensure that the new lock is a good fit.

You may want to replace window locks your lock for a variety of reasons, including when you suspect that someone else is holding the key or you've got a new roommate. You could save money if you remove the lock yourself instead of hiring a professional. The process is easier than most people think, and it can be done in a few minutes.

Remove the handle and trim of your door. Then, pry the trim off using a flat screwdriver. You should be able to twist off the majority of it. In some instances you may be able to take off the handles completely. Next, search for a pinhole on the inside of the handle, and insert a straightened clip into it. This will trigger the release mechanism and allow you to remove the handle from the door. Then, look for a small tab that is located inside of the lock and press it with a screwdriver that is flat. Once the spindle is removed, you can take off the cylinder and housing.

Making a choice for a new lock

There are a lot of options available when it comes to choosing the right lock. Take a look at various types of double glazing window locks repairs, and find one that matches your door's style. Consider the backset (the distance between the edge of the door and the center of the lock hole) and the cross bore (small hole along the edge of the door frame). Select a lock that will fit the door's thickness and swing.

The American National Standards Institute and BHMA have graded most door locks to give an idea of their strength and the t was used to lock your old lock with a new one by sliding it into the case and tightening the set screws. The process of reinstalling the component that connects a cylinder to a lock indicator stem is also essential. You can do this by pulling three tabs in the back of the cylindrical with needle-nosed pliers. Then, you can connect the remaining smaller bracket to the back of the cylinder. Then, you must put back in the strike plate and latch plate as well as the retaining ring connected to the top lock cylinder.

Installing the new lock

Start by measuring the door's width if you are replacing an existing lock. Most locksets for residential use are designed for doors with a thickness of 1 3/8 to 3/4 inch. If your door is thicker, you will need a thick door kit that includes longer screws as well as longer tail pieces (for door knobs) or spindle extension (for deadbolts).

Most locks come with a comprehensive instruction booklet that will assist you in installing the new hardware. Be sure to read the instructions thoroughly before beginning the process to ensure that you've followed all the steps. The manual will give you an idea of how much skill is required to finish the task. You might want to seek out a friend who has worked with locks for assistance if you are changing locks for the first time.

Before installing the new lock, it's a good idea to cover the holes with tape the old hardware. This will prevent the screws from slipping out of the holes, and will protect any tiles you might have installed in the area. It also shields your tiles from any damage caused by dirt, rust and grime. SECURAM Touch comes with an ad-hoc strip of masking tape or gaffer tape, but you can use any tape you have.

Once you've removed the screws holding the interior portion of the lock section to the exterior side, pull it straight away. This must be done quickly to prevent the lock from accidentally closing and damaging the mechanism.

Fit the new latch bolt into the upper cross bore of the new lock if it has one. Make sure that you place it in the proper location, which is indicated by an arrow. Then, place the latch plate over the bolt and secure it in place.

Screw the deadbolt into the jamb of the door. Try the deadbolt a few times by throwing it to see if it extends into the strike plate. If you're using an electronic smart lock, make sure to follow the included instructions for programming it. This requires downloading an app and registering your email address, verifying your identity, then accessing the wireless network to add your device.